vcc-vsim 24 : ref-out 23 : vfil 22 : vref 21 : v-backup 20 : vbat2 19 : gnd1 18 : delaycap 17 : xpowergood 48: sw3-input 47: sw3-output 46: sw1-input 45: sw1-output 44: cont4 43: vbat4 42: vbat4 ...
http://www.fujitsu.com/downloads/MICRO/fma/pdf/e427801.pdf
The VSIM switch path has a low RON characteristic to insure minimal voltage drop in the ... when the control voltage applied to the SEL pin is lower than the supply voltage (VCC).
http://www.idt.com/?genID=HS421V16&source=products_genericPart_HS421V16
Vcc maximum value LIMIT VS1= 1MA,0 ;Maximum value of lCC2 INI=5.3V,OV ... Open, Limit : -10 ~ 10uA 7V a. ILIL ( Input Leakage / Input Low ) VSIM=0V,R2V, M8UA
http://www.ececs.uc.edu/~wjone/ATE.pdf
One for +VCC, one for -GND and two for the turning direction. Before you close the casing ... A.A. van Zoelen / vsim@mail.com Updated: 26 Oct. 1999
http://vsim.freeservers.com/walk-kit.html
Compiling module VCC # -- Compiling module GND # -- Compiling module INV # -- Compiling ... vsim +notimingchecks +TESTNAME=sample_smoke_test0 -L work work.boardx01 glbl
http://forums.xilinx.com/xlnx/board/message?board.id=PCIe&thread.id=64
Error: (vsim-3063) C:/projects/ivac/design/asms/syn/simulation/modelsim/asms_04.vo(25067) ... wire vcc = 1'b1; altsyncram_v9d2 auto_generated(.q_a({q_a_unconnected_wire_15,q_a ...
http://www.alteraforum.com/forum/showthread.php?p=15633#post15633
... avss - PCmax DCDC rail4 SIM_CLK D-O H10 gnddig - vsim avss - PCmax SIM SIM_RESET D-O H9 gnddig - vsim avss - PCmax SIM SIM_IO D-I/O G7 gnddig - vsim avss - PCmax SIM SIM_VCC A-O G8 gnddig - vsim avss ...
http://www.atmel.com/dyn/resources/prod_documents/doc2742.pdf
vsim -L XILINXCORELIB_VER -L UNISIMS_VER -L UNI9000_VER -L SIMPRIMS_VER -L CPLD_VER -L AIM ... Error* view VCC is not defined for inst VCC_0 "E:/project/mysoc/PPM/V1.0/sender/src/fifo ...
http://forums.xilinx.com/xlnx/board/message?board.id=ISE&message.id=4136
... What combination of PRE and CLR do I use to make DFF work in mentor? Set both to 1(Vcc). ... 7.? I'm getting expired license using vsim. What do I do? If you are having license ...
http://pages.cs.wisc.edu/~karu/courses/cs552/spring2008/wiki/index.php/Main/ToolsFAQ
... on the pkt_proc design using VHDL and get an error that "Symbol vcc ... Fatal: (vsim-3420) Array sizes do not match. Left is (2047 downto 0)
http://www.xilinx.com/ise/embedded/ml300_v2pdk/members/general_faq.htm
Error: (vsim-13) Recompile ../simulation/postsynth.YourTopLevelEntity (def_arch ... IL(CLK,GL,Y,RESET); input CLK; output GL, Y; input RESET; wire CLKP, VCC ...
http://www.actel.com/download/software/libero/libero70rlsp1.aspx
Tektronix Scopes VCC VW-300 VHDL XUP-V2Pro ... A simple Batch File. First, use vlib to create a design ... vcom -93 Node_TB.vhdl vsim -t 1ps -lib work Node_TB
http://www.bioinspired.com/users/ajg112/electronics/modelsim.shtml
... Vcc Motor | | +----- Engage ... Reverse 74xx139 ASCII DRAWING (c) AA van Zoelen http://www.xs4all.nl/~vsim ...
http://www.geocities.com/SouthBeach/6897/rigter/wr_4.html
vsim -t ps alu_tb -sdfmax :alu_tb:ali=/heim/yngve/vhdl/syntese/alu_temp_1/simulation ... SIGNAL vcc : std_logic := '1'; SIGNAL devclrn : std_logic := '1'; SIGNAL devpor : std ...
http://doc.uib.no/wiki/Synthese
CONNECTOR DESCRIPTIONS: ICSP: Pin # Signal Name 1 RST 2 VCC 3 GND 4 PGD 5 PGC 6 NC This connector allows ... SIM-CARD: Pin # Signal Name 1 VSIM 2 SIMRST 3 SIMCLK 4 GND 5 NC 6 SIMDATA This is standard SIM card ...
http://www.olimex.com/dev/pdf/PIC/PIC-GSM.pdf
Failed to open SDF - Fatal: (vsim-SDF-3445) Failed to parse SDF file." (Xilinx Answer 16182 ... 5.1i Virtex-II PAR - Change in how VCC connections are routed for Partial Reconfiguration ...
http://www.xilinx.com/support/answers/16272.htm
USB: Pin # Signal Name 1 VCC 2 USBDM 3 USBDP 4 GND This is standard USB Type B connector for ... and GSM module or between ATMega32 and GSM module. SIM-CARD: Pin # Signal Name 1 VSIM 2 SIMRST 3 ...
http://olimex.com/dev/pdf/AVR/AVR-GSM/AVR-GSM.pdf
Modelsim PCBs Switch Debouncing Tektronix Scopes VCC VW-300 VHDL XUP-V2Pro ... work vcom - 93-pedanticerrors -lint +acc=v LCDDriver.vhdl vcom - 93 LCDDriver_TB.vhdl vsim ...
http://www.bioinspired.com/users/ajg112/electronics/lcds.shtml
Cisco MGX 8250 Software 1.1.42 Version Software Release Notes Cisco WAN MGX 8850, 8230, and 8250 Software
http://www.cisco.com/en/US/docs/switches/wan/mgx/mgx_8850/software/release/notes/rn1142.html
max2_VSim: Launches the Powerview ViewSim simulator. max2_VTrace: Launches the Powerview ... Under Signal Names, type one or more names with up to 20 total name characters in the VCC ...
http://www.altera.com/support/software/eda_maxplus2/viewlogic/motive/motiveall.html |
|
